Education
Hot Water and Heating for Schools, Academies & Universities
Design, supply and support for commercial hot water, heating and low carbon applications.
Hot Water and Heating for Schools, Academies & Universities
Design, supply and support for commercial hot water, heating and low carbon applications.
Hot Water and Heating for Schools, Academies & Universities
Future-Proofing your Investment in Sustainability
Reduce Risk
Address how Valuable Space can be Best Utilised
Managing a More Sustainable School Estate
Future-Proofing your Investment in Sustainability
Reduce Risk
Address how Valuable Space can be Best Utilised
Managing a More Sustainable School Estate
Adveco can help you at every point of your project. For Design, Supply & Support we have you covered.
Improve Efficiency
For a calculable reduction in energy consumption to reduce operational costs
Tackle Emissions
Reduce or completely remove emissions from estate building.
Enhance Existing Systems
Adapt or replace existing hot water and heating with low carbon hybrid systems that economically bridge to future sustainable technologies.
Adveco’s Air source Heat Pumps, Solar Thermal, Heat Recover and Packaged Hybrid Systems and Plant Rooms can help you achieve Net Zero by 2050.
Solar Thermal provides an effective way to offset the new financial burden that comes from moving from cheap gas to currently far more expensive electricity. A ten-year return on investment becomes very achievable, and, with zero emissions, the undisputed carbon and cost savings make this technology increasingly more viable. Solar has always been used as a preheat with coldest water possible to maximise the efficiency and output: this gives maximum free heat with no carbon emissions. But there is a good case now for using solar thermal with heat pumps and electric if set up as a mid-heating system which can lower both carbon and cost. READ MORE…
Essentially making use of free heat energy, when operating for typically six hours per day, across either gas or electric only systems, heat recovery for installations can average as much as 155 kWh/week per site. This saved energy means less overall power demands and therefore reduced emissions, so a school can not only be seen to be addressing environmental issues but will also be making operational cost savings. READ MORE…
Select an Application Below:
Avoid the pitfalls of over-engineered, over-complicated and over-sized and therefore costly to build and operate school hot water and heating systems.
Following a project installation, our specialist engineers will commission the system, assuring it has been correctly and safely fitted in accordance with the manufacturer guidelines. This thorough site assessment is also available to you whether commencing a new build project or considering options for refurbishment.
From this assessment we can liaise with building consultants or contractors on new build projects or recommend a replacement design. Our Application Design team is available throughout this process to support and respond to specific needs or changes in planning. Supplied designs come with an accurate estimate for the application
If you need convincing, why not arrange for one of our specialist engineers to visit your location and assess your specific needs at no cost. We can then recommend a new or replacement design to maximise your investment in a more sustainable future.
Free Site Assessment: please fill out the form below and we will be in contact within 24 hours of submitting.
Free Site Assessment: please fill out the form below and we will be in contact within 24 hours of submitting.
Adveco has designed and built a full prefabricated plant room at a school in Berkshire, providing the new school building with a modern hot water and heating system situated inside a self-contained rooftop plant room. Adveco’s packaged plant rooms are the easiest way to achieve the maximum potential within the limited space schools have available whilst also keeping costs and time of projects reduced with off-site construction. READ MORE…
Avoid the pitfalls of over-engineered, over-complicated and over-sized and therefore costly to build and operate school hot water and heating systems.
Following a project installation, our specialist engineers will commission the system, assuring it has been correctly and safely fitted in accordance with the manufacturer guidelines. This thorough site assessment is also available to you whether commencing a new build project or considering options for refurbishment.
From this assessment we can liaise with building consultants or contractors on new build projects or recommend a replacement design. Our Application Design team is available throughout this process to support and respond to specific needs or changes in planning. Supplied designs come with an accurate estimate for the application
If you need convincing, why not arrange for one of our specialist engineers to visit your location and assess your specific needs at no cost. We can then recommend a new or replacement design to maximise your investment in a more sustainable future.
Adveco can help you at every point of your project. For Design, Supply & Support we have you covered.
Free Site Assessment: please fill out the form below and we will be in contact within 24 hours of submitting.